球探网即时比分直播

  • Huixian Xinda Textile Machinery Fittings Co., Ltd.
  • Huixian Xinda Textile Machinery Fittings Co., Ltd.
  • Huixian Xinda Textile Machinery Fittings Co., Ltd.
news

Introduction to GA615, 1515 automatic loom

Release: hnfzpj Browse: 21223 times

(I) Machine use and scope of use

This machine is mainly suitable for weaving plain weave cotton fabric, twill cotton fabric and general chemical fiber fabric. If a multi-arm lifting device is installed, fabrics with complicated structures can be woven. Woven from plain weave to 16-ply weave.

(Two) technical characteristics

1. Automatic shuttle change without stopping the type.

2. Divide left-handed car and right-handed car.

纺织机械设备1515K织布机

3.Wing width

(1) Plain weave: 1350mm (56 inch loom), 1500mm (63 inch loom), 1600mm (67 inch loom), 1800mm (75 inch loom).

(2) Dobby: 1350mm (56 inch loom) 1500mm (63 inch loom), 1600mm (67 inch loom), 1800mm (75 inch loom).

4. Crankshaft speed: 160-190r / min (56 inches), 155-180r / min (63 inches), 150-170r / min (67 inches), 145-160r / min (75 inches)

双梁GA615织布机后视图

5. Chest beam height: 838mm

6. Number of shuttle boxes: 1X1

7. Angle between steel reed and shuttle plate: 86.5 °

8. Shuttle capacity: 10

9. Warp beam diameter: 495mm (large side disc 550mm).

10. Beam-to-disk distance: 1380mm (56 inch loom), 1555mm (63 inch loom), 1656mm (67 inch loom), 1860mm (75 inch loom).

11. Full diameter of cloth roll: 300mm.

12. Motor speed: 960r / min.

13. Motor power: 0.8KW.

纺织机械设备织布机

14. Motor model: FO-53-6 (left and right) or FO3-50-6N.

15. Electrical switch: 1515-DZ4-25 / 330 (4A) button switch. GA615--LA20-2H push button switch.

16. Comprehensive magnetic starter: QZ73-4G.

17. Machine Dimensions:

Width: 2696mm (56 inches), 2866mm (63 inches), 2968mm (67 inches), 3171mm (75 inches).

Depth: 1656mm.

Height: 1540mm (plain), 2250mm (multi-arm).

18.Machine weight (excluding motor)

56 inch loom: about 940KG (plain weave), 1140KG (multi-arm).

63 inch loom: about 1000KG (plain weave), 1200KG (dobby).

67 inch loom: about 1025KG (plain weave), 1225KG (dobby).

75 inch loom: about 1100KG (plain weave), 1800KG (dobby).

织布机装车

(Three) transmission mechanism

1. Transmission method: single motor V-belt drive.

2. Control mode: One-sided switch handle controls clutch and brake device.

3. Clutch type: conical friction disc type.

4. Braking type: steel belt braking.

5.The pedal shaft and the turning speed ratio are 1: 2.

(IV) Main institutions and their specifications

1. Let-off agency

(1) Type: Semi-positive and semi-negative automatic let-off, automatic adjustment of warp tension.

(2) Warp core diameter: 110mm

(3) Diameter of warp disc: 495mm, 550mm.

2.Warp stop device

(1) Type: mechanical menopause.

(2) Rack motion cycle: The crank shaft rotates twice.

(3) Number of menopause films: 4 columns.

3.Opening mechanism

(1) Type: The opening of the upper roller hanging heald on the inside tread plate.

(2) Diameter of pedal shaft: 42mm.

(3) Number of heald frames: 2 pages of heald frames (can be modified to 5 pages or 16 pages of dobby heald lifting device)

4. Shuttle mechanism

(1) Type: lower throw shuttle.

(2) Shuttle size: length 343mm (13.5 inches), width 44.5mm, height 33.5mm (left and right hands).

(3) Skin crust type: active skin crust.

(4) Skin knot size: 105mm in length, 30mm in width, and 32mm in height.

(5) Shuttle rotor diameter: 76mm.

75英寸织布机

5. Beating mechanism

(1) Type: The crank shaft is used to beat the weft.

(2) Diameter of crank shaft: 40mm.

(3) Radius of crank shaft: 76mm.

(4) The center distance of the two curved turns: 1540mm (56 inches), 1714mm (63 inches), 1816 (67 inches), 2019mm (75 inches).

(5) Hand-held type: bearing-hand type.

(6) Length in hand: 289mm.

(7) Diameter of hand plug: 25mm.

(8) Distance from center of hand to center of rocking axis: 685mm.

(9) Shaft type: whole root.

(10) Diameter of rocking shaft: 38mm.

(11) Type of sley: wooden structure.

(12) Length of shuttle board: 1423mm (56 inches), 1699mm (63 inches), 1597mm (67 inches), 1902mm (75 inches).

(13) Length of shuttle box bottom plate: 581mm on the switch side and 600mm on the shuttle side.

6.Warp protection device

Type: swim 筘.

75英寸织布机车间

7.Reeling mechanism

(1) Type: Seven-gear intermittent coiling.

(2) Weft density range: 16-32 pieces / cm.

(3) Bristle roll diameter: 127mm.

(4) cloth guide roller diameter: 32mm.

(5) Cloth roll diameter: 95mm.

8.Stretching device

(1) Type: Single-row copper barbed ring roller type.

(2) Number: left and right.

(3) Weft shearing hammer: The impact of the sley makes the shearing hammer act.

9.Weft breaking automatic stop device

(1) Type: weft cam control side weft fork or point-pecking weft detection.

(2) Rewinding and unwinding device

10.Weft supply device

(1) Type: Automatic shuttle change.

(2) Shuttle: vertical single row.

1515双梁织布机

(3) Shuttle capacity: 10.

(4) Shuttle change induction device: a probe shuttle change induction device is used (for a less demanding fabric, a weft fork change shuttle induction device can also be used).

(5) Shuttle changing safety device: When the shuttle changing mechanism fails, stop immediately to avoid damage to the parts.

(6) Shuttleless and side shuttle parking device: When there is no shuttle or shuttle position in the shuttle warehouse, it will automatically stop immediately.

(7) Weft insertion prevention device: It can avoid defects such as burrs and double wefts, and improve fabric quality.

Five, the main equipment specifications

1. The total length of the weft is 180mm, and the diameter of the head is 27mm.

2. Steel reed

Total length: 1394 (56 inches), 1568mm (63 inches), 1669mm (67 inches), 1873mm (75 inches).

Height: 120mm.

3. Heald length: 305mm plain or twill, 330mm dobby.

4. Menopause film: 120mm long and 11mm wide.

5.V-belt: A2286.

1515-56 dobby multi-shuttle loom manufacturer


From "GA615 Automatic Loom Parts Atlas"


Links: China Textile Network, China Manufacturing Network, Global Trade Network , Simon International, Xuanda Textile Accessories, Shun Enterprise Network, 258 Platform, China Textile Accessories Network , China Textile Network
Copyright © 2016 Huixian Xinda Textile Machinery Fittings Co., Ltd. All rights reserved [Administration]
Address: Comprehensive Building of Chengguan Town Mosque, Huixian City, Henan Province Contact: Yang Shengjun Mobile: 15237383444
Tel: 0373-6235050 Fax: 0373-6235050 E-mail: 309816745@qq.com Record Number: Henan ICP No. 18009479-1 Henan Public Security No. 41078202000454
Customer Service
Customer service one:
click here
Customer service two:
click here
Service Hotline: 0373-6235050